Products Archive - Page 7 of 22

Custom Specifications

Email These Product Specifications

We'll send these specifications along with your message.

Recipient Email*
Email multiple recipients by separating email addresses with a comma.
Sender's Email*
Subject*
Message

Info for the CAMSS 26Q39-CT

26’ width x 39’ length x 12’ 10" height
Heavy-duty aluminum frame
Heavy-duty commercial fabric

The CAMSS 26Q39-CT is great middle ground between our most popular and tested models, the CAMSS 20Q and the CAMSS30. Giving you the extra headroom for offices or even storage uses like the CAMSS30 and also still being quick to setup like the CAMSS 20Q.

General Info

Measures 26’ wide x 39′ long x 12’ 6″ tall
Usable area of 1014 square feet
1200 lbs unpackaged
Assembles in 1 hour with trained six-person crew
Used for offices, storage, kitchen, dining and housing

Cover / Ends

13 oz/sq yd heavy-duty commercial fabric
Total of four (4) mesh windows with covers
Fabric includes UV inhibitors and is mold and rot resistant.
Fire resistant fabric that meets NFPA 701
Cover and ends are radio frequency welded

Personnel Entries

Centered on ends of the shelter
Two (2) aluminum personnel door
- 30” wide x 80” high
- Locking flush mount handle

Frame

Made from lightweight, high-strength aluminum
Continuous base frame
Frame components are interchangeable and color coded to speed assembly
Pre-drilled base frame for easy anchoring
Base frame includes connection points to secure cover to frame
Frame is corrosion resistant aluminum

Electrical - OPTIONAL

Single phase electrical panel
- One (1) 20A breaker
- One (1) light switch with breaker
- Four (4) twist lock cable connectors
Two (2) outlet lines with a total of twenty-four (24) quick connect 110V outlets
Twelve (12) quick connect incandescent lights with protective cages
20 ft. 20A power cable included

Anchoring

Double headed 18” base frame spikes
- Lag screws can be substituted for double headed spikes if specified

Engineering

Engineering calculation demonstrate shelter performance will meet a 100 mph wind load per ASCE 7-16 with high wind kit
Engineering calculations demonstrate shelter performance will meet a 20 psf ground snow load per ASCE 7-16 with high wind kit

*Design loads assume that actual soil conditions will meet one of the following in accordance with ASTM D-2487/2488:

Sand gravel / very dense sand
Hardpan / Asphalt

**Fabric weights are nominal

***Dimensions are nominal

CAPTCHA

CAMSS 26Q39-CT

Part Number: CAMSS-26Q39-CT-T (Tan)

Part Number: CAMSS-26Q39-CT-G (Green)

Part Number: CAMSS-26Q39-CT

Part Number: CAMSS-26Q39-CT-W (White)

General Info

Measures 26’ wide x 39′ long x 12’ 6″ tall
Usable area of 1014 square feet
1200 lbs unpackaged
Assembles in 1 hour with trained six-person crew
Used for offices, storage, kitchen, dining and housing

Cover / Ends

13 oz/sq yd heavy-duty commercial fabric
Total of four (4) mesh windows with covers
Fabric includes UV inhibitors and is mold and rot resistant.
Fire resistant fabric that meets NFPA 701
Cover and ends are radio frequency welded

Personnel Entries

Centered on ends of the shelter
Two (2) aluminum personnel door
- 30” wide x 80” high
- Locking flush mount handle

Frame

Made from lightweight, high-strength aluminum
Continuous base frame
Frame components are interchangeable and color coded to speed assembly
Pre-drilled base frame for easy anchoring
Base frame includes connection points to secure cover to frame
Frame is corrosion resistant aluminum

Electrical - OPTIONAL

Single phase electrical panel
- One (1) 20A breaker
- One (1) light switch with breaker
- Four (4) twist lock cable connectors
Two (2) outlet lines with a total of twenty-four (24) quick connect 110V outlets
Twelve (12) quick connect incandescent lights with protective cages
20 ft. 20A power cable included

Anchoring

Double headed 18” base frame spikes
- Lag screws can be substituted for double headed spikes if specified

Engineering

Engineering calculation demonstrate shelter performance will meet a 100 mph wind load per ASCE 7-16 with high wind kit
Engineering calculations demonstrate shelter performance will meet a 20 psf ground snow load per ASCE 7-16 with high wind kit

*Design loads assume that actual soil conditions will meet one of the following in accordance with ASTM D-2487/2488:

Sand gravel / very dense sand
Hardpan / Asphalt

**Fabric weights are nominal

***Dimensions are nominal

Email This Product

Customize The CAMSS 20Q UAV

We'll Send this product's picture, description, and details along with your message.

Recipient Email*
Email multiple recipients by separating email addresses with a comma.
Sender's Email*
Subject*
Message

Info for the CAMSS 20Q UAV

View online

Heavy Duty Hard Flooring
Double Zipper Vehicle door for UAVs and Personnel Door on other end
20’ width x 32’6” length x 10’ height
Engineered to withstand extreme weather conditions

The CAMSS 20Q Small Shelter System has been proven in the field for over 2 decades. Designed as a semi-permanent military shelter that can last 15 to 20 years, it is able to withstand extreme temperatures, high winds, and heavy snow loads. That is why you can trust your UAV to stay protected with the CAMSS 20Q UAV package. Changing out the standard personnel door for an easy but effective double zipper vehicle door allows access for small fixed wing UAVs. The addition of heavy duty hard flooring ensures a solid material to support the weight of UAV and maintenance equipment. Lastly, Fluorescent lights enable effective operations around the clock.

View and download full product specifications online.

CAPTCHA

Email

Customize The CAMSS 20Q UAV

We 'll send a picture, description, and custom specifications along with your message.

Recipient Email*
Email multiple recipients by separating email addresses with a comma.
Sender's Email*
Subject*
Message

Info for the CAMSS 20Q UAV

View this shelter online

Heavy Duty Hard Flooring
Double Zipper Vehicle door for UAVs and Personnel Door on other end
20’ width x 32’6” length x 10’ height
Engineered to withstand extreme weather conditions

General Info

Measures 20’ wide x 32’6” long x 10’ tall
Usable area of 650 square feet
1150 lbs unpackaged
Assembles in 30 minutes with trained four-person crew
Used for UAV maintenance, UAV hangar

Cover / Ends

15+ oz/sq yd Mil-Spec 44103D fabric
Vestibule connectors over entries can be used to connect to other shelters or vestibules
Includes one (1) set of two (2) 18” ECU ports with a cable port
Total of two (2) mesh windows with wind resistant blackout covers
Twelve (12) guy ropes for high wind
Can connect multiple shelters end to end with integrated connector flap
Built in infrared (IR) blocking
Fabric includes UV inhibitors and is mold and rot resistant.
Fire resistant fabric that meets NFPA 701
Cover and ends are radio frequency welded
Each end panel includes mesh attic vent with cover

Vehicle Door

One (1) double zipper entry
- 14′ wide x 6′ high
- Tie offs to hold door open

Personnel Entry

One (1) aluminum personnel door
- 30” wide x 80” high
- Locking flush mount handle
- Secured to the shelter without penetration of the fabric
- Centered on one end of the shelter

Frame

Made from lightweight, high-strength aluminum
Arches are made with 2”x 2” aluminum square tube
Continuous base frame to provide vector proofing
Frame components are interchangeable and color coded to speed assembly
Pre-drilled base frame for easy anchoring
Base frame includes connection points to secure cover to frame
Frame is corrosion resistant aluminum
Removable end base frame to allow vehicles full access through vehicle doors

Fabric Floor

15+ oz/sq yd non-slip Mil-Spec 44103D
Floor system is secured to the base frame
Removable for cleaning and replacement without disassembly of shelter
Continuous hook and loop perimeter for vector proofing to keep bugs and critters out

Extreme Temperature Kit

Shelter includes an internal liner system that helps to maintain internal working conditions of 40° – 80° F in ambient temperatures of -25° to 125° F when supported by a 5-Ton military environmental control unit
Air sock runs the length of the shelter and has spot cooling
8 oz/sq yd Mil-Spec fabric
Liner is flame resistance per test method ASTM D6413
- After flame – 2 seconds max
- Char length – 6” max

Electrical

Shelter System includes complete internal electrical system
Single phase electrical panel
- Two (2) GFCI 20A breakers
- Two (2) 20A breakers
- One (1) light switch with breaker
- Four (4) twist lock cable connectors
Two (2) outlet lines with a total of twenty-four (24) quick connect 110V outlets
Six (6) Ruggedized Fluorescent Tube Lights
50 ft. 20A power cable included

Anchoring and High Wind Kit

18” double headed base frame spikes
Twelve (12) guy ropes and guy spikes

Spares / Repair Kit

30 day spares/repair kit
Patch materials for cover, liner, and floor which are all air transportable without special hazmat requirement

Tools

Verified manual
Sledge hammer
Spike puller
Four (4) pull over ropes

Life Expectancy/Warranty

Shelter has a usable life of 10 years and a 20 year storage life
Shelter includes a standard manufacturer’s warranty

Shelter Packaging

Wood crate
Forklift ready and Export approved
43” W x 101” L x 30” H
310 lbs (empty crate)
1460 lbs (total weight with shelter)
Six fit on a 463L pallet

Testing

Provide U.S. government lab test with quote demonstrating shelter will maintain internal temperatures of 40°F to 80°F in ambient temperature of -25°F to 125°F when supported by a 5-ton military environmental control unit.
Provide U.S. government test report preformed to Test Operations Procedure (TOP) 10-2-175 Tents and Shelters wind test procedures of shelter with quote.
Provide stamped engineering calculations with quote of this shelter demonstrating shelter performance meets a 100 mph wind load per ASCE 7-16.
Provide U.S. government test report preformed to Test Operations Procedure (TOP) 10-2-175 Tents and Shelters snow load test procedures of shelter with quote.
Provide stamped engineering calculations with quote of this shelter demonstrating shelter performance meets a 20 psf snow load per ASCE 7-16.
Provide U.S. government test report preformed to Test Operations Procedure (TOP) 10-2-175 Tents and Shelters blowing rain procedures of shelter with quote.
Provide U.S. government test with quote demonstrating shelter is deployable after 20 Set-up/Strikes durability and drop test.

*Design loads assume that actual soil conditions will meet one of the following in accordance with ASTM D-2487/2488:

Sand gravel / very dense sand
Hardpan / Asphalt

**Fabric weights are nominal

***Dimensions are nominal

CAPTCHA

Shop

Customize The CAMSS 20Q UAV

Customize The CAMSS 30EX UAV

Customize The CAMSS TAC LT Shelter System

Customize the CAMSS30 Medium Shelter System

Customize the CAMSS 12EX20-CT

Customize the CAMSS 18Q32-CT

Customize the CAMSS 20EX Medical Shelter System

Customize the CAMSS 20Q Medical Shelter System

Customize the CAMSS 20Q SMALL SHELTER SYSTEM (SSS)

Customize the CAMSS 21Q42-CT

Customize the CAMSS 24Q48-CT

Customize the CAMSS 26Q39-CT

Custom Specifications

Email These Product Specifications

We'll send these specifications along with your message.

Info for the CAMSS 26Q39-CT

CAMSS 26Q39-CT

Email This Product

Customize The CAMSS 20Q UAV

We'll Send this product's picture, description, and details along with your message.

Info for the CAMSS 20Q UAV

Email

Customize The CAMSS 20Q UAV

We 'll send a picture, description, and custom specifications along with your message.

Info for the CAMSS 20Q UAV

Request Quote

Contact Info